Bob's Machine Shop, Inc. Division of RSM International, Inc

BMS International Inc.'s transom wedges are high quality aluminium and offer 4 degrees of change for boats transoms.0D;
0D;
This is great for boats that need the engine to have additional "tuck under" or "negative trim".0D;
0D;
Standard BIA bolt pattern, and very light weight!

12 volt solenoid.0D;
0D;
Can handle running amps of 40amps, with spikes up to 70amps.0D;
0D;
Not for continue "ON" use, such as high powered light, but intermittent uses such as jack plates, tilt/trim, trim tabs.

BMS International Inc.'s hydraulic pump assembly is S.A.E. J1171 certified for the highest quality available.0D;
0D;
Adjustable up to 3000 PSI can suit most applications, although we have it adjusted at the proper PSI for our jack plates. Can be used for other applications such as tilt/trim, or trim tabs.0D;
0D;
Includes backing (mounting) plate, 2 high quality solenoids, and 16' wiring harness with inline fuse.0D;
0D;

Our hydraulic jack plates offer a minimum of 7.5 inches of vertical lift for outboard engines. Lift the engine vertically reduces the drag of the lower unit, increasing speed, fuel economy and allowing the boater access to shallow water.0D;
0D;
Different setbacks allow the engine to sit farther away from the hull, and bite 'clean water'. The further back you set the engine, the higher you can raise it, as the water coming off the hull rises.0D;
0D;
BMS jack plates offer the quickest lift time, lightest weight on

BMS International Inc. Offers top quality engraving of backing plates for OEM boat builders, and dealers alike.0D;
0D;
Low minimum quantities required, and no setup fees. 0D;
0D;
In addition to adding a nice custom touch, also helps distribute load across transom.

BMS International Inc. offers setback spacers for boaters who need just a small amount of additional setback.0D;
0D;
Available in 2", 3/4", and 5/8" sizes.0D;
0D;
Made out of aluminum.

BMS International Inc. offers boats solid motor mounts for their outboard engine.0D;
0D;
Much stronger than stock mounts, they are great for racing applications.

BMS's nose cones offer low water pick ups for boaters looking to maximize performance. Run your engine higher, and still be able to maintain proper water pressure.

Now be able to control your hydraulic jack plate from anywhere on the boat without running wires. Easy to install, and can be added onto older jack plates, this is a great solution to boaters with a tower, or while upfront trolling!

BMS International Inc.'s patented True Tracker stabilizer plate is one of the most popular in the industry.0D;
0D;
Made out of high quality aluminum, they do not flex under load the way a plastic one does, offering greater lift and contributing to better "hole shots".0D;
0D;
The patented rudder/fin design encapsulates water around the propeller, help boats with chime walk, and reduces porpoising. Also help keep the boat on plane at lower speeds.0D;
0D;
Available for most outboard engines, and limited I/O applications.

BMS International Inc.'s "Hot Shot" foot throttle offers the ability to move the boats throttle to the floor and work like a car's gas pedal.0D;
0D;
With different mounting points for different engines throttle cable style, BMS's Hot Shot can be used on most applications.0D;
0D;
Great for safety, keep both hands on the steering wheel!

Offering 14inches of vertical travel, the BMS international Inc. Kicker Jac is the perfect solution to those with auxiliary outboard engines that need to get it up and out of the water when not in use, and offering the convenience of hydraulic functionality. Rated for 40HP

Add 8-12HP to your Yamaha engine with Bob's Yamaha exhaust tuner.0D;
Fits all Yamaha V6 carburated, EFI, HPDI and 3.1 & 3.3 liter ( '97 - current ).0D;
0D;
Also cheaper than stock replacement!

BMS International Inc. offers a replacement for Mercury 2.0, 2.4 and 2.5liter owners.0D;
0D;
Cheaper than a stock replacement, and offering 6-12 HP gains, as well as a "meaner" exhaust tone.0D;
0D;
All aluminum and made in the USA.

BMS International Inc.'s thru-hull fitting style A are similar to other thru-hull fittings, but require less drilling into the hull of the boat.0D;
0D;
By attaching via 1 large nut from the inside of the transom, it is the only hole the boater needs to drill in the boat. Also there are no screws to wear out.

BMS is proud to present the Versa Jac, a manual jack plate that is easy to use and ready for engines upto 300HP. With the purchase of an 'upgrade kit' the owner can convert to hydraulic at a later date. This is a great way to get boaters on the water faster without spending lots of money all at once.

Tall or short boaters will appreciate the ability to adjust their foot throttle with BMS International Inc.0D;
0D;
Locks into position with a spring loaded pin, pull up and slide to proper distance for the driver.

This is the first ultra high quality jack plate ever designed for smaller engines by any manufacturer. Our mini versa jacs offer the same fit and function as our full size line. Designed for engines between 3hp-50hp, these smaller engines will be able to utilize their full performance with Bob's mini versa jac plates.

Thru-hull fitting for running hydraulic hoses through the hull of the boat.0D;
0D;
Attaches to hull via 3 small screws from the outside of the hull.

Made to resemble out high quality line of jack plates, our new Fixed Setback Brackets are perfect for the boater that needs setback but no need to adjust the height of their engine.0D;
0D;
Offered in 4 and 6 inch models.

Offering high quality and affordability, BMS International Inc. is pleased to now offer starter motors.0D;
0D;

Engineers at BMS International Inc., took their existing jack plate and re-engineered the whole product for additional strength to handle 350+HP engines, but V6 and V8!!!

Our new jack plate will increase speed, increase rpm, reduce drag, improve efficiency and reduce fuel consumption.