Yacht Devices Ltd.

The Barometer measures atmospheric pressure within the range from 300 to 1100 hPa or mbar (225 to 825 mmHg), it provides chart plotters and displays with barometric pressure data. The Barometer can be configured to turn on or off specified channels of digital switching equipment. The conditions can be either the actual atmospheric pressure or the difference between actual pressure and the pressure 30 minutes or hour ago. Stores 48 hours of data in the RAM. The firmware can be updated over CAN.

The Thermometer performs measurements within the range from -55 to +125°C (-67..+257°F) with absolute measurement accuracy of ±0.5°C. It can be configured by the user to display data as "Air temperature" (factory setting), "Sea temperature", "Temperature in the refrigerator", "Temperature in the engine room", "Bait Well Temperature", etc. The Thermometer stores last 48H data in RAM, can manage digital switching channels by user rules and support firmware updates over the CAN.

The Sensor measure the temperature of extremely hot gases, solids and liquids within the range from 0 to +800 °C (+32 to 1472 °F). With factory settings it transmits measured data as "Air Temperature" (because this data type is supported in all MFDs), but can be reconfigured to display "Exhaust Gas Temperature", "Heating System Temperature", "Engine Room Temperature", etc. It can mange digital switching channels, stores 48H history and support firmware updates.

The Circuit Control contains four latching (bi-stable) relays, which can be managed from connected control buttons with LED indicators or over NMEA 2000 with standard messages or from the screen of a modern chart plotter. It capable of switching the direct current (DC) and alternating current (AC) loads up to 400V. Well suitable for a small vessels, can be controlled from your smartphone (inexpensive NMEA 2000 Wi-Fi Gateway is required), certified for NMEA 2000.

The Switch Control allows viewing of the state and the management of four channels of an NMEA 2000 switch bank from the connected buttons with LED indicators. It is designed to work in tandem with Circuit Control YDCC-04 (contains four latching relays) or Alarm Button YDAB-01 and is compatible with other NMEA 2000 digital switching devices managed by standard NMEA 2000 PGNs 127501 and 127502. The Device has 10 terminals for connection of four momentary push buttons with an LED indicator.

Smart multiplexer with five NMEA 0183 ports and one SeaTalk port, auto detection of port speed and easy configuration with a click of a button! And, of course, it has flexible filters, routing rules, and supports firmware updates. The Multiplexer has six configuration presets with different port speeds and routing schemes. Presets can be selected by pressing a hidden button. Ports can be routed to themselves, which allows multiplexing of data from SeaTalk and 5 different NMEA 0183 talkers.

The sensor provides chart plotters and instrumental displays with humidity and air temperature measurements and calculated dew point temperature. The device is plug and play; you only need to plug it into a NMEA 2000 backbone to get readings on all chart plotters and instruments on board. This product can be used for weather monitoring and fog prediction; mold prevention by monitoring of water intake or moisture condensation in lockers. Support firmware updates and digital switching.

The Gateway to NMEA 2000 supports the two protocols that work over J1708: the standard J1587 used by many manufacturers and the proprietary Volvo Penta protocol used in engines with EDC I, for example KAD 44, KAD 300, TAMD 73..75; also compatible with EDC II (e.g. D12C-A MP). The Gateway can be easily configured and updated from MicroSD card, supplied with NMEA 2000 Micro Male or SeaTalk NG connector.

The Router connects all marine and mobile devices easily, and even allows management of your vessel from a web browser without internet connection or installed software. It is equipped with NMEA 2000 and SeaTalk ports, two NMEA 0183 ports, has three TCP/UDP data servers and a built-in web server, where you can easily configure it or update the firmware. It creates its own Wi-Fi network or can be connected to an existing Wi-Fi network.